Friday, January 10, 2014

Friday Finds on Artfire: Snowflakes

We've sure had a lot of the white stuff around here lately.  There's a huge maple tree in our front yard that collects the fluffy, wet kind of snow on its branches and then when the temperatures rise above freezing, the tree rains on the yard.  The kids think it's quite fun.  Me - not so much - especially when I have to go under the tree to get to my car.

But it sure does make for some gorgeous landscapes and, up close, it makes for some lovely artistic inspiration.  So enjoy these snowflakes from Artfire sellers:



You can also enjoy these photos of my own work inspired by snowflakes:
Currently only available by special order.  Contact me for more information.

Available in my Artfire shop.

This one sold a couple of years ago.
Enjoy!
Korrina

Tuesday, January 7, 2014

Polymer Clay Tutorial: Argyle Cane


New year, new state/city/house, fresh start on my business, my blog and my homeschool.  (Not necessarily in that order.)

It’s been nearly a year since my last tutorial here so I figured I’d better make this one awesome.  I don’t know whether this cane fits the bill or not, but I had a lot of fun designing it.  I’m using the website Days of the Year to help me find themes for my blog posts and for this week my inspiration was “Argyle Day” on January 8th. I love geometric shapes and patterns and this one looked like a simple but fun challenge to start the year off with.  Hopefully you can find something fun to do with this cane.

This tutorial assumes you know the basics of polymer clay caning – conditioning, shaping, cane reduction, etc.

Tools Needed:
Flexible Tissue Blade
Pasta Machine
Acrylic Roller

Supplies Needed:
1 oz each of four colors polymer clay
½ oz of a fifth color for the flower centers
½ oz black or white clay for the stitches
(amounts are approximate)

Instructions:
Condition all of your colors of clay.  I am using purple, yellow, teal, orange, pink and black for the stitches.

Roll the fifth color of clay (the ½-oz one) into log for the center of your flowers.

Roll your petal color into a long snake and cut into 8 equal pieces.  Adjust the thickness of them to fit around the center log.

Pack the areas between the petals with wedges of the color you will be using for the flower backgrounds.  I always overpack and trim the excess.

Trim the excess to get something as round as possible to minimize distortion of the flower.

This looks pretty good.

Wrap the cane in a couple of sheets of thick clay.

Mark a square with your blade on one end of the cane.  Make the marks line up with the petals as shown.  You will want to leave a little of the background clay around the petals closest to the edges, but not too much. 

If you are lacking a little (or a lot of) clay at the corners, add some pieces.

Trim the cane into a square.

Reduce the cane to ½ its original width (twice the length)...

...trim the ends and cut it in half.

With your remaining two colors (not including the black or white), make square logs the same size and shape as your flower canes.

Arrange your four logs as shown, with the two flower canes touching at the inside corners.  Compress well and reduce slightly.

Cut the cane into three pieces as shown, getting as close to the middle of each section as possible.

Roll out a sheet of black or white clay as thin as you can.  (I used setting 7 on my Atlas.) 

Cut a strip as wide as the length of your cane.  Cut the end even.  Cut a narrow strip of clay from the end...

...and while lifting the blade just barely off the work surface, pull it toward you so the tiny strip of clay stays attached to the blade.  (You can use your fingers but leaving it on the blade will make the next step easier.)

Lay the strip close to the edge of one of the smaller chunks of clay you cut off the cane earlier. 

Repeat until you have covered the entire cut side in strips of black or white clay stripes.  (Make sure your stripes are going the length of the cane, not the width – they will lay the same direction as the stripes that resulted from cutting the flower in half.) 

Lightly roll over the stripes with your acrylic roller to compress them into the base a little.

Stick the piece back to your cane with the stripes inside.

Repeat the above steps on the other cut part of the cane so you have to rows of “stitching” in your cane.  Compress it well.  Now rotate the cane 45 degrees and make two cuts perpendicular to the first two. 

Add the stripes as before.  Reassemble your cane and reduce it a little.

You can reshape the square into a diamond now and then reduce the diamond-shaped cane, or you can reduce it square and then reshape.  Either way, both reduce and reshape.

And there you have a really fun cane that would be great for covering eggs or Christmas ornaments or whatever strikes your fancy.

I covered a pen with it.

You can also make argyle without the flowers and with fewer colors.  Here I used two colors – plum and a pale sage green.  Make two blocks of each and press them into a four-square checkerboard pattern...

...make the cuts...

...add the stripes, turn, repeat...

...reduce and reshape.  Use it to make something creative.  (I haven’t used this one yet.)

I would love to see what you come up with!

Enjoy!

Korrina

Friday, January 3, 2014

Friday Finds: Chocolate Covered Cherries

Did you know that today is Chocolate Covered Cherry Day?  Okay, so there's a "day" for just about anything anymore.  But don't let that spoil an excuse to enjoy a yummy treat!

When you're done, check out these great items from Artfire.  All of them are inspired by the flavors and colors of the candy of the day!



Oh, and while I'm at it: Years ago, I asked my then-7-year-old to choose the colors for some beads and the following are what she came up with.  I've always called them my "cherry chocolate" beads.  Unfortunately the quality isn't good enough to sell, but they make me happy when I look at them.

Enjoy! Korrina